Hello,
I would like to know if the SMART value of ‘0’ for “Available_Reservd_Space”, as shown by smartctl (under Linux), is an indication for my “SanDisk SSD U100 128GB” reaching end of “life” ?
I would also be grattefull is someone could point me to some method/documentation on how to interpret the “raw” data for this particular model, and particularily those allowing an estimation of remaining lifetime.
(Below is the full output of smartctl for my SSD drive)
Thanks in advance and regards,
Tsintao
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11-1-amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SanDisk SSD U100 128GB
Serial Number: XXXXXXXXXXXX
LU WWN Device Id: 5 001b44 73f91f0a7
Firmware Version: 10.02.00
User Capacity: 128’035’676’160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Nov 3 17:26:34 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 32) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 2962
12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 926
171 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0
172 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 0
173 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 30
174 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 884
187 Reported_Uncorrect 0x0002 100 100 000 Old_age Always - 0
230 Unknown_SSD_Attribute 0x0002 100 100 000 Old_age Always - 100
232 Available_Reservd_Space 0x0003 100 100 005 Pre-fail Always - 0
234 Unknown_Attribute 0x0002 100 100 000 Old_age Always - 184
241 Total_LBAs_Written 0x0002 100 100 000 Old_age Always - 4078956678
242 Total_LBAs_Read 0x0002 100 100 000 Old_age Always - 6336472316
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported